Jump to content
  • Sign Up
  • 0

2002 gmc ABS on , no codes , no speedo


jempey

Question

hi , driving me crazy , 2002 gmc 2500hd , auto trans , 4wd , 6.0l , app 250,000 km , 4dr xcab , long box , factory 2" lift , . my ABS lamp is on , there are no codes , no speedometer ,  ABS lamp behaves normal , comes on , goes out , comes back on. originally had a vss code , so i installed a non gm vss , still the same , when i drive 1/4 block the park and brake light come on , they go out after restart and only come on when moving , no speedo , i sent the ABS module away to be repaired , twice , first time it came back it was  the same but wouldn't recognize that i had unplugged the vss as a test , the module will recognize either front abs sensor wires disconected , code for them , and then recognize that i plug them back in , i checked the fuses , i took the wiring harness from the vss to the pcm and  verified that the two wires from the vss are ok , everybody i ask says that it is impossible to have an ABS lamp on and no codes, the module repair man told me i had a cheap code reader so i had a professional shop reader diagnose the codes ,  ($ 200.00) same thing , ABS on , no codes available , driving test showed no output from vss , put the old original vss back in , same thing , i bought a used complete ABS unit yesterday , stripped the module off , plugged into my truck , the ABS lamp went off ,finally , truck running or shut off . so i went for a test drive , no speedo still , and then the ABS lamp came back on and the park/brake lamp too , no codes still , park/brake lamp off when restarted but ABS still  illuminated . also replaced the vehicle  battery , i'm working outside in canada and it's about 0F , not much fun with those little t20 module bolts.they want $750 canadian dollars at the GM local dealer for a new module . is it possible the ignition switch is haywire ? is there a vss speed buffer in this truck ? and will it hurt my trans to operate like this , it shifts hard like a race car , been 2 mos without using the truck , thanks , jim. i should also mention that i cleaned and verified the 2 ground points under the cab and the ground under the battery on the frame, ran jumpers from battery to engine, frame , firewall etc, no better, unplugged pcu and visually checked the pins for corrosion , truck was from british columbia and has minor corrosion , almost none, no road salt area , . we fixed a pontiac vibe that had no speedo , ABS lamp wasn't on , researched that the two front wheel sensors ran to the abs module to make the speedo work , no vss, we replaced the ABS module and all is working , i thought similar situation here but this truck has a vss, the vss wires run directly to the pcm . where they go next i don't know. i purchased a cd of a factory service manual , but it has 23,000 pages and no index that i could find , if i had the proper page numbers to search perhaps i could do more , so if you can give me the page numbers it would help a lot, also it's very slow to load as too much data .

Edited by jempey
additional info
Link to comment
Share on other sites

3 answers to this question

Recommended Posts

  • 0

Sounds like you have the 4l85e for that year. I know there is 2 VSS on that tranny front and rear of the tranny- and they need to able to communicate with eachother. I noticed you talk about changing one. Did you do both? Also I would reset the Throttle position sensor for the hard shifting issue. The TPS and vss's all communicate to eachother to calculate load and line pressures for the tranny. I dont know much about this issue but to me almost sounds like a faulty cluster- but that doesnt explain the hard shifts. Personally I would probably drop the pan change all of the electrical components (shift solenoids, Tcm, wire harness etc.) inside the tranny plus swap in a new filter. That will just rule out internal electrical components. The kits for these trucks are under $200 and fairly easy to replace. It's just dirty and time consuming. Hope you get it figured out! Good luck.

Sent from my SM-G960U using Tapatalk

Link to comment
Share on other sites

  • 0

thanks , but i have the manual transfer case which does not have the second speed sensor , the speedo doesn't work somehow due to the speed sensor ? or the ABS module ? and as there is no speed input to the computer the truck is shifting hard as the computer  doesn't know what speed the truck is moving at , trans oil and filter is new fairly  recently , i need to know why the ABS lamp is on , but does not throw codes ?????

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.