Jump to content

2019 Sierra AT4 level/wheel/tires mod


Recommended Posts

On 2019-06-20 at 4:13 PM, Joe98 said:

Congrats Nik;  looks great eh...haha.  Fellow Canuck here.  Haven’t seen too many long box models in the crew cabs.  Love your wheel choice.  Any clearance issues or rubbing?  

Thanks! Haha and no I haven’t seen many at all which I love. 

 

I also haven’t had any issues with rubbing at all. They fit great! 

 

Link to comment
Share on other sites

Here’s my 2019 SLT 4x4. 

 

In the front I installed a set of AT4 front struts that I bought locally from a guy on offer up. In the back I went with a 2” block. 

 

Tires are Nitto Terra Grappler 285/65/20 on stock 20” wheels. 

C00BCFAF-ECC3-4481-BEE1-4B373914DC04.jpeg

Link to comment
Share on other sites

45 minutes ago, RVR2MTN said:

Here’s my 2019 SLT 4x4. 

 

In the front I installed a set of AT4 front struts that I bought locally from a guy on offer up. In the back I went with a 2” block. 

 

Tires are Nitto Terra Grappler 285/65/20 on stock 20” wheels. 

C00BCFAF-ECC3-4481-BEE1-4B373914DC04.jpeg

So you essentially have an AT4 height suspension, without level.  Any rubbing with the 285/65/20?

Link to comment
Share on other sites

  • 3 weeks later...

Hey guys, new to the forum.  I'm getting my AT4 today and already ordered the motofab 1.5" level and going to get some 22" GMC replica wheels to put on.  Will I be okay with a 35x12.50x22 tire?  The offset on the wheels will be +24 which is pretty close to the factory I think.  

  • Like 1
Link to comment
Share on other sites

On 6/30/2019 at 12:08 AM, josephearljones said:

1.5" motofab, 20x10 fuel tech, 33x12.50 Toyo R/T.

More pics after I get it cleaned upe8ea85746a9bfab3240e8e7aaf612864.jpg

Sent from my Pixel 3 XL using Tapatalk
 

Awesome looking!

Did you get the Black or Anthracite color on the wheels? Do you currently get any rubbing? How far do the tires stick out from the fenders? I like these wheels and I am considering going with the Nitto Ridge Grapplers in a 295/65 (34x11.5) or 35x11.5 so that I won't need to go higher than a 1.5" Motofab lift. I believe that the offset and the 12.5" width would cause rubbing and require a bigger lift and possible major trimming.

Link to comment
Share on other sites

2" Rough Country 1318 level

295/60R20 (34" x 11.7") Nitto Ridge Grapplers

AMP Powersteps

BAKFlip MX4 bed cover

 

I have no rubbing, but it is very close on the upper control arm.  The ride has not changed, and the truck is perfectly level.  I am very impressed with the upper ball joint and CV angles.  More pics to follow. 

side view.jpg

front tire.jpg

rear quarter view.jpg

front tread.jpg

Edited by thsoccer3
  • Like 2
Link to comment
Share on other sites

2" Rough Country 1318 level

295/60R20 (34" x 11.7") Nitto Ridge Grapplers

 

View of CV angle and two half-decent views of upper ball joint (tires are straight in top photo, and wheel is at full lock in the second photo).

CV angle.jpg

suspension.jpg

  • Like 1
Link to comment
Share on other sites

I am contemplating adding BORA hub centric wheel spacers for a slightly more aggressive look only.  I only want to space a little, as I do not want rock chips on the rocker panel and lower doors.  I also do not want to cut or modify factory lugs.  Because of this, I am interested in a hub-centric spacer that only fits over the factory lug without providing new lugs.  I know my needed wheel spacer specifications are as follows:
 
6 x 139.7 pattern
78.1mm hub
106mm bore
 
This raises a few questions in which I seek your expert opinion.
 
1.  Does only adding spacers without any additional changes require a front-end alignment?
2.  Do you know the maximum distance spacer I can safely add utilizing the factory lugs with the OEM wheel?
3.  I have no rubbing; they are for looks only.  On factory lugs, I am assuming it would be close to a 0.500" maximum.  Would the minimal spacer even be noticeable (worth it)? 

offset.jpg

Edited by thsoccer3
Link to comment
Share on other sites

1 hour ago, thsoccer3 said:

2" Rough Country 1318 level

295/60R20 (34" x 11.7") Nitto Ridge Grapplers

AMP Powersteps

BAKFlip MX4 bed cover

 

I have no rubbing, but it is very close on the upper control arm.  The ride has not changed, and the truck is perfectly level.  I am very impressed with the upper ball joint and CV angles.  More pics to follow. 

side view.jpg

front tire.jpg

rear quarter view.jpg

front tread.jpg

Wow...looks perfect...couldn’t get it any better !

  • Like 1
Link to comment
Share on other sites

Awesome looking!
Did you get the Black or Anthracite color on the wheels? Do you currently get any rubbing? How far do the tires stick out from the fenders? I like these wheels and I am considering going with the Nitto Ridge Grapplers in a 295/65 (34x11.5) or 35x11.5 so that I won't need to go higher than a 1.5" Motofab lift. I believe that the offset and the 12.5" width would cause rubbing and require a bigger lift and possible major trimming.
Thanks man! I went with anthracite.

The wheels stick out approx .5" - .75". I had no rubbing initially, but after things settled I had a pretty annoying rub in reverse at about 3/4 lock. There is a little flange where the lower bummer connects to the air damn, I trimmed that off and the problem was solved.

Sent from my Pixel 3 XL using Tapatalk

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.