Post your 2014+ wheel/tire set-up

[Boltman21]

 

With a 3" front level and stock rear block, isn't it a little higher in front than in the rear? Or is it exactly level?

Measured from pavement to center of fender (top center over wheel) front is exactly 1/4" higher in the front vs rear on mine. Looks exactly level to the naked eye though.

[Boltman21]

Boltman, do you have a side shot. I have a 3 inch as well and your stance and the way the wheels sit is exactly what I'm looking for. Curious to see how much tire is past the fender

 

Sent from my Nexus 6P using TapatalkSu

Sure do. Took this one the day I got my wheels and tires installed. -20 off set was key in pushing mine out (aggresive look I wanted) Increase chance of rubbing on turns though.

 

 

 

 

Looks really nice

Thanks buddy.

Edited February 18, 2017 by Boltman21

[Luster]

Measured from pavement to center of fender (top center over wheel) front is exactly 1/4" higher in the front vs rear on mine. Looks exactly level to the naked eye though.

Looks good.

[5RWill]

I love these wheels and tires

[Jeff5347]

Sure do. Took this one the day I got my wheels and tires installed. -20 off set was key in pushing mine out (aggresive look I wanted) Increase chance of rubbing on turns though.

 

Thanks buddy.

Thanks. Looks perfect. Exactly what I want. I have the 3 inch as well. Lot of clearance work?

 

 

Sent from my Nexus 6P using Tapatalk

[5RWill]

For those of you running RTs on 17s what PSI are you running? My local place airs everything to 40ish so I'm at 42-45psi right now and want to air down to 35 truthfully but would that be too low for this tire?

[5RWill]

I aired down to 37 and the ride is 10x better. On the way out to the farm pressure was at 45/46 and man it was rough.

[chevy2tuff2006]

I love these wheels and tires

Will you just stop posting pics.........just when I thought I was done buying parts for my truck, I wasn't going to buy wheels but your making it hard......lol

[5RWill]

Sorry man I can't help myself lol just do it you won't regret it.

[Krey1500]

Here is where I needed to trim to get a 33.4"x12.3 tire on 18x9 -12 rims to work with no rubbing. It wasn't too bad but I did need to eleviate some metal

What psi u running?

[Krey1500]

Best i could do before leaving work, then it started pouring down rain :/ love it though. 295/70/17 RTs with Method NVs. Stoked with how it turned out and surprisingly no rubbing, even with the little 1.8" the Bilstein's provide. Now i just wish i had 6112s and new control arms lol.

What psi r u running them at?

[5RWill]

What psi r u running them at?

 

The local place had them at 45. I couldn't stand it, dropped it to 36/37 yesterday. It's 10x better now. Truthfully i like 35 and maybe even 30 in some instances but right now i'm satisfied with 36/37.

[eMc9002]

 

The local place had them at 45. I couldn't stand it, dropped it to 36/37 yesterday. It's 10x better now. Truthfully i like 35 and maybe even 30 in some instances but right now i'm satisfied with 36/37.

 

Your setup just cost me some money. Just ordered the 17" NV's in black. Saw your post on the hide for that Razor too, small world. I was tempted but you got me on the wheel's first.

[5RWill]

Lol sorry man! I wish i could've talked to you about the Razor ha i need some cash at the moment. My laptop is going downhill and i also want to fund a 4.5-27x56 Gen II razor for my match rifle. You'll enjoy the methods though. They look great on these trucks.

 

I will say at first i thought zero offset would be fine as it's almost flush, but upon heading out to the farm yesterday they do stick out some. I'll need to get some fender flares later on to take care of that. I also am rubbing just a tad at full lock on the sway bar. But it's barely. Other than that no rub at all.

Edited February 19, 2017 by 5RWill

[eMc9002]

Lol sorry man! I wish i could've talked to you about the Razor ha i need some cash at the moment. My laptop is going downhill and i also want to fund a 4.5-27x56 Gen II razor for my match rifle. You'll enjoy the methods though. They look great on these trucks.

 

I will say at first i thought zero offset would be fine as it's almost flush, but upon heading out to the farm yesterday they do stick out some. I'll need to get some fender flares later on to take care of that. I also am rubbing just a tad at full lock on the sway bar. But it's barely. Other than that no rub at all.

 

Damn I just ended up selling my 4.5-27 Razor. Could have done a swap trade, did drop some money on coilover's though so there is that lol. I ordered the 0 offset's as the same as yours. Do you think the +18 would have been a better choice with less rubbing?